Question: I recently read an article about preparing your home for an earthquake and it mentioned that improperly braced water heaters can be a cause of house fires that start because of a major quake.
Our water heater is in a closet inside our house, and it does not have any sort of bracing. Can you explain what I can do to make it more earthquake-safe?
Your Handyman:Â An unbraced or incorrectly braced water heater does pose a threat to your home in the event of a moderate to severe earthquake.
Correctly bracing a water heater is a simple thing to do, but I regularly see water heaters that have been installed incorrectly by both plumbers and homeowners.
If a water heater is knocked over during a quake, the natural gas supply line or the 220-volt electrical wiring could be ripped out of the wall by the weight of the falling tank, and a fire could possibly start if the gas or electrical service is not quickly shut off.
If the gas and electrical connection lines are rigid and not flexible connections, then they may be cracked or damaged during an earthquake. Even if the tank doesn’t tip over, a fire hazard can occur from a gas leak.
Seismic bracing straps for a water heater can be purchased at most hardware or plumbing stores, and detailed instructions will be included for a correct installation.
The kit will have two thin metal adjustable straps, and one strap needs to be located at the top third of the tank, and the second strap needs to be at the bottom third.
Each strap needs to have both ends lag-screwed into the wall studs and then connected across the front of the tank with brackets that can be tightened together by turning a threaded bolt with a wrench.
On a flat wall, the water heater needs to be pressed firmly against the wall by tightening the straps. Likewise, if the water heater is situated in a corner, it needs to be pressed into the corner by the straps.
If there is some obstruction like plumbing preventing the tank from being in full contact with the wall, wood blocking can be lag-screwed horizontally to the wall studs and the tank can then be pressed against the wood blocking.
A water heater with seismic straps placed correctly on the tank and fastened correctly to the wall studs, is still not correctly braced until the tank is firmly in contact with the wall or the blocking.
This is a very common oversight, probably simply due to the installer not taking the time to read the installation instructions. If the tank is not in firm contact with the wall, the straps will provide less protection during an earthquake.
Damage to furniture and structures during an earthquake often occurs when the house starts to move out of sync with the contents. Instead of moving together as a unit, they strike together or collide, and unsecured objects simply get knocked over after being hit by either the wall or by another object of greater mass.
Your water heater or a large bookcase that has a large mass will have greater momentum while moving and will hit the wall with much greater force.
A water heater or large piece of furniture that is securely braced will, in theory, shake and sway with the house rather than slamming against the walls and toppling over.
If the water heater is not held firmly against the wall by the straps, it will strike against the wall and the straps as the house shakes. The sheer weight of the tank may tear the straps off the walls and the tank may still fall.
The final step in preventing your water heater from starting a fire during an earthquake is being able to quickly shut off the gas supply to your house.
Know where your gas meter is located, make sure it is easily accessible and leave a wrench at the meter for emergency use in case you cannot get access to your tools.
Even better is to have your plumber install a seismic shutoff valve that automatically turns off the gas supply when shaken by an earthquake.
• • •
Question: Our house is a typical Goleta tract home that was built in the 1960s, and my husband and I have owned it and lived here since 1975.
We have done a little remodeling; we both really love the look of granite and want to get granite countertops for our two bathrooms.
However, the built-in bathroom cabinets are in good shape and we don’t want to replace them.
Wwhat all is involved with this project?
Your Handyman: The first step in any remodeling project is the most fun, which is shopping for materials.
Granite is beautiful, very popular, and Santa Barbara has many tile, stone and countertop dealers that sell granite for countertops in two basic ways.
The first way that granite is sold is in a large slab that is then cut down into the sizes needed for your project. This is the usually the most expensive way to purchase granite in that you typically must buy the entire slab and there may be extra material that you pay for but do not need.
The second way is to purchase a precut granite countertop section that is already cut to the typical depth and width of a countertop, matching back splash is already cut, and a finished bull nose or ogee detail is already fabricated on the exposed edge.
Many of these precut sections are being quarried and fabricated in China, are very affordable, and there will be a minimum of waste material left over.
After you have selected your countertop material, the next step is to have a contractor disconnect the plumbing on your old sinks and remove the old countertops and sinks.
If the sinks are in good condition, you can reuse them and just replace the faucets and drain assemblies.
Some cabinets will require that a plywood top be fastened onto the top of the cabinets to help support the weight of the granite. Your contractor can tell you if this is needed.
The shop where you purchased the granite can arrange for the cutting of the sink openings in the granite and for the drilling of the holes needed for the faucets.
Depending on the style of sink you choose, there are a couple of different ways to install them, and your counter fabricator will take care of this for you.
After the new granite is in place, the installer will then set the backsplash, your contractor will connect the plumbing for the sinks, and your project is completed!
Granite needs to be regularly sealed with a chemical sealer that is available at the shop where you purchased the granite. Follow the manufacturer’s application instructions on the sealer bottle and your granite will look beautiful for years.
MORE MARK BAIRD


